Last updated 15 October 2026
Cleanroom and Pharmaceutical Workwear: Specifying to a Cleanliness Class
Cleanroom and pharmaceutical garments are the one workwear category where the buyer usually arrives with the requirement already written, because the plant is validated to a cleanliness class and the garment is part of how that class is maintained. That makes this an unusually precise purchase: the garment construction, the fabric's particle and static behaviour, the laundering and the way garments are issued and worn all have to line up with a documented procedure. Where it goes wrong is almost never the fabric — it is a garment that was bought against a class without the test evidence, or a construction with a feature that sheds or traps particles.
Request a bulk quotation WhatsApp usKey takeaways
- Send the plant's class and its validated garment procedure. If the requirement is written down, it decides the garment, and it is far more specific than a general cleanroom brief.
- Construction detail is where contamination comes from. Bound or taped seams, no external pockets, no exposed fastenings, and a fabric with continuous filament rather than a short-staple yarn that sheds.
- Particle control and static control are different requirements, and a garment can be excellent at one and poor at the other.
- Ask for the test report against the construction being supplied. A statement about the fabric family is not evidence for the garment your operators will wear.
- The laundry is a controlled process, not a wash. Degradation, re-dressing and rejection rules are how a garment programme stays inside a validated class, and those rules are the plant's to set.
1. The plant's own class is the specification
Most pharmaceutical, medical device, electronics and food-hygiene plants we supply are classified to a cleanliness class and validated against it. The garment requirement follows from that class, and it is usually already documented.
| What the plant's procedure usually states | What it means for the order |
|---|---|
| The cleanliness class of each room | Garment type and coverage per area, and how much of the body has to be covered |
| Garment construction rules | Bound seams, no pockets, covered fastenings, specific cuffs and collars |
| Fabric requirements | Continuous filament, low-linting, and the static behaviour the area requires |
| Garment life and laundering rules | How many cycles before replacement, and what disqualifies a garment |
| Dressing and issue rules | Who gets their own garment, where it is stored, and the gowning sequence |
| Testing requirement | Whether the garment or the fabric must be tested, to which method, and how often |
Send us the section of your validated procedure that covers garments, exactly as written. Where it names a test method or an acceptance figure, tell us which, and we will tell you what we can evidence against it before the order rather than after it. This is the one sector where guessing the requirement is guaranteed to waste a purchase order.
2. What makes the garment different
A cleanroom coverall looks like a coverall and is engineered like nothing else in this catalogue.
- Seams are bound, taped or welded. An open seam releases fibre into the room. The seam finish is the first thing a technical buyer inspects and the first thing a cheap garment gets wrong.
- No external pockets, and no exposed fastenings. Pockets collect particles and give the wearer somewhere to put something that is not allowed in the room.
- Continuous filament yarn. Short-staple yarns shed fibre by design. A fabric built for low linting behaves differently over the whole service life, not just on the first day.
- Static behaviour engineered in. Where the area requires it, a conductive filament is woven in and grounded — it is not a surface finish, and it cannot be added to a finished garment.
- Comfort is a compliance issue here too. An operator who is too hot in a coverall will open it, remove the hood, or leave the room — and all three defeat the class.
3. Particle control and static control
| Requirement | What it addresses | What it is not |
|---|---|---|
| Particle control | How much fibre and particulate the garment releases, and how well it contains what the wearer sheds | It says nothing about static |
| Static control | Preventing charge build-up where a discharge can damage product or ignite a solvent vapour | It says nothing about particle shedding |
| Both | Common in electronics, in solvent-handling pharmaceutical areas and in powder handling | Requires a construction evidenced against both, with both reports |
| Barrier performance | Resistance to liquid or microbial penetration, where the area requires it | A separate product class with its own testing — see the boundary section |
Where a plant needs static control, the requirement is usually expressed as a range or a resistance figure with a named test method rather than as the word "antistatic". Give us the figure and the method and we will tell you what we can evidence. The same applies to particle shedding: a method and an acceptance limit, or nothing testable.
4. Laundering and garment life
In every other sector on this site the laundry affects appearance. Here it affects whether the validated class holds, which is a different order of consequence.
- Controlled laundering, not laundry. Cleanroom garments are usually processed on a validated cycle and finished in a way that keeps them clean until use, rather than coming back in a polybag from a commercial laundry.
- Degradation is a rejection criterion. Wear, seam damage and repaired tears all change shedding behaviour. Plants set rejection rules for a reason, and the garment has to be built to survive the number of cycles those rules allow.
- Tell us the temperature, the chemistry and the cycle count. A garment specified against a domestic wash and processed on a validated high-temperature cycle will shrink, and a shrunken cleanroom garment is a rejection, not a misfit.
- Sterilisation where applicable. If the garment is processed by a method beyond laundering, say so at enquiry stage — it changes both the fabric and the trim.
5. Dressing, issue and control
Garment control is usually the plant's own procedure, and it changes what is worth buying.
| Procedure | What it means for the order |
|---|---|
| Garments issued individually and stored in the gowning room | Individual marking, a wide size spread, and a storage and replacement discipline |
| Garments pooled and issued by size | More garments per worker, and a size set that fits everyone in the room rather than the average |
| Dedicated garment per room or grade | Colour coding by area, so a garment from the wrong zone is visible immediately |
| Hoods, boots and face coverings as part of the set | The set is bought together, because a mismatched hood is where coverage usually fails |
| Visitors and auditors needing garments | A small stock in assorted sizes, held separately from production garments |
6. What we do not certify
This is the sector where a supplier's scope statement is most likely to be tested, so here it is plainly.
- We do not certify a cleanliness class. A class belongs to your room, not to a garment. What we can supply is a garment and the test reports for the properties it is specified against — and if the requirement is a report we cannot obtain, we will say so before the order.
- We do not supply sterile or barrier products. Sterile drapes, gowns with a barrier claim and products that have to demonstrate microbial or liquid penetration performance are a different product class, and we do not make them.
- We make no antimicrobial claim and no claim that a garment removes the need for a validated laundering process.
- We do not advise on your validation. Whether a garment is acceptable in a validated area is a decision for your quality function, on their evidence. Our job is to tell you precisely what the garment is made of and what has been tested.
7. A specification you can hand over
| Line | What to write |
|---|---|
| Area and class | The room or grade, and the coverage the garment has to provide |
| Garment set | Coverall, frock, trouser and top, hood, boots, face covering — as a set per area |
| Construction | Seam finish, cuffs, collar, closures, and the absence of pockets or exposed fastenings |
| Fabric | Continuous filament, weight, and the static behaviour the area requires |
| Static and particle requirements | The test method and the acceptance figure, as your procedure states them |
| Laundering and life | Process, temperature, chemistry, cycle count, and any sterilisation step |
| Issue and marking | Individual issue or pooled, size spread, colour coding by area, and marking method |
| Packaging | How the garment has to be packed to arrive clean, and how it is stored before use |
8. Where we ship cleanroom garments
| Market | What the orders look like | Page |
|---|---|---|
| Malaysia | Electronics and semiconductor supply chain, with the most formalised cleanroom culture in our market set | Malaysia · compliance |
| Singapore | Pharmaceutical, biomedical and electronics, with the requirements already written before the enquiry | Singapore |
| Indonesia | Pharmaceutical manufacturing and electronics assembly, often alongside a factory uniform programme | Indonesia · compliance |
| Vietnam and Thailand | Electronics, medical device and pharmaceutical plants with export-quality validation | Vietnam · Thailand |
| Egypt and South Africa | Pharmaceutical manufacturing for domestic and regional supply | Egypt · South Africa |
| Nigeria and Ghana | Pharmaceutical and food-hygiene operations, often on a hygiene rather than a full cleanroom requirement | Nigeria · Ghana |
Where a plant is validated to a specific class, the acceptability of a garment is usually decided by the plant's own quality function on the basis of test evidence, and different regulators in these markets assess that differently. Send us what your quality function requires and we will tell you what we can evidence.
9. Frequently asked questions
Frequently asked questions
What is the minimum order for cleanroom garments?
300 pieces per style and colour for a trial order, 1,000 pieces for standard pricing and 5,000 and above for the best price. A set — coverall, hood, boots — can be ordered as one programme, and the colours or grades in the same fabric and style share one minimum.
Can you certify the garment to a cleanliness class?
No, and any supplier who offers to is worth questioning. A cleanliness class belongs to your room. What we can supply is the garment and the test reports for the properties it is specified against. If your procedure requires a specific report we cannot obtain, we will tell you before the order.
Do you have garment shedding test data?
Where a construction has been tested, we will give you the report and the method it was tested to. Where it has not, we will say so rather than describe the fabric as low-linting. Send the method and acceptance figure your procedure names and we will tell you what we can evidence against it.
Can you supply antistatic cleanroom garments?
Yes, with a conductive filament woven into the fabric rather than a surface finish, which is the only way static behaviour survives laundering. Give us the resistance range and the test method your procedure names and we will confirm what we can supply.
Is the garment sterile when it arrives?
No. We are not a sterile or barrier product manufacturer. Garments are packed to protect them in transit and are processed through your own validated laundering and gowning procedure before use.
What sizes should we hold?
More than a normal workwear programme, because cleanroom garments are often pooled rather than issued individually and a garment that does not fit gets opened or removed. Send a size set first and fit it on operators in the actual room.
Do you supply hoods, boots and face coverings?
We supply fabric hoods, boots and coverall sets. We do not supply disposable items, masks or sterile products. Where your set includes one of those, that is another supplier and we will say so.
How do we reorder without changing the garment?
Send the previous order reference and ask us to reserve a fabric lot. In this sector a change of construction or fabric between batches is not a cosmetic issue, so keeping the specification on file with one supplier is worth more than a few cents of unit price.
Quality checklist
- Room class and coverage
- Seam and closure rules
- Static range and method
- Shedding method and figure
- Laundering and cycle count
- Issue, marking and storage
Send the procedure, not a summary
Give us the class, the construction rules, the test methods your quality function requires and the laundering process. You will get a costed quotation and a written statement of exactly what we can evidence and what we cannot.